一．问题说明 测试环境中出现的小问题，因为虚拟机之间经常复制来复制去，导致网卡配置这块的不一致现象。 配置文件的信息：

[root@ora10g network-scripts]# catifcfg-eth0
DEVICE="eth0"
NM_CONTROLLED="yes"
ONBOOT=yes
TYPE=Ethernet
BOOTPROTO=none
IPADDR=192.168.1.12
PREFIX=24
GATEWAY=192.168.1.1
DEFROUTE=yes
IPV4_FAILURE_FATAL=no
IPV6INIT=no
NAME="System eth0"
UUID=5fb06bd0-0bb0-7ffb-45f1-d6edd65f3e03
HWADDR=08:00:27:BD:A6:ED
 

[root@ora10g network-scripts]# catifcfg-eth1
DEVICE="eth1"
NM_CONTROLLED="yes"
ONBOOT=yes
TYPE=Ethernet
BOOTPROTO=none
IPADDR=192.168.1.13
PREFIX=24
GATEWAY=192.168.1.1
DNS1=8.8.8.8
DEFROUTE=yes
IPV4_FAILURE_FATAL=yes
IPV6INIT=no
NAME="System eth1"
UUID=9c92fad9-6ecb-3e6c-eb4d-8a47c6f50c04
HWADDR=08:00:27:6E:86:10
 

这里对应的是网卡名称是eth0和eth1. 但是如果我们使用ifconfig 命令查看：

[root@ora10g network-scripts]# ifconfig -a
eth2     Link encap:Ethernet  HWaddr08:00:27:BD:A6:ED 
         inet addr:192.168.1.12 Bcast:192.168.1.255 Mask:255.255.255.0
         inet6 addr: fe80::a00:27ff:febd:a6ed/64 Scope:Link
         UP BROADCAST RUNNING MULTICAST MTU:1500  Metric:1
         RX packets:187 errors:0 dropped:0 overruns:0 frame:0
         TX packets:59 errors:0 dropped:0 overruns:0 carrier:0
         collisions:0 txqueuelen:1000
         RX bytes:16356 (15.9 KiB)  TXbytes:6116 (5.9 KiB)
 
eth3     Link encap:Ethernet  HWaddr08:00:27:6E:86:10 
         inet addr:192.168.1.13 Bcast:192.168.1.255 Mask:255.255.255.0
         inet6 addr: fe80::a00:27ff:fe6e:8610/64 Scope:Link
         UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
         RX packets:1357 errors:0 dropped:0 overruns:0 frame:0
         TX packets:1099 errors:0 dropped:0 overruns:0 carrier:0
         collisions:0 txqueuelen:1000
         RX bytes:120604 (117.7 KiB)  TXbytes:115937 (113.2 KiB)
 
lo       Link encap:Local Loopback 
         inet addr:127.0.0.1 Mask:255.0.0.0
         inet6 addr: ::1/128 Scope:Host
         UP LOOPBACK RUNNING MTU:16436  Metric:1
         RX packets:8 errors:0 dropped:0 overruns:0 frame:0
         TX packets:8 errors:0 dropped:0 overruns:0 carrier:0
         collisions:0 txqueuelen:0
         RX bytes:480 (480.0 b)  TXbytes:480 (480.0 b)
 

这里的网卡名称是eth2和eth3. 二．解决方法 修改 /etc/udev/rules.d/70-persistent-net.rules文件中的映射关系就可以了。 --修改之前：

[root@ora10g network-scripts]# cat/etc/udev/rules.d/70-persistent-net.rules
# This file was automatically generated bythe /lib/udev/write_net_rules
# program, run by thepersistent-net-generator.rules rules file.
#
# You can modify it, as long as you keepeach rule on a single
# line, and change only the value of theNAME= key.
 
# PCI device 0x8086:0x100e (e1000)
SUBSYSTEM=="net",ACTION=="add", DRIVERS=="?*", ATTR{address}=="08:00:27:d4:ab:67",ATTR{type}=="1", KERNEL=="eth*", NAME="eth1"
 
# PCI device 0x8086:0x100e (e1000)
SUBSYSTEM=="net",ACTION=="add", DRIVERS=="?*", ATTR{address}=="08:00:27:af:2b:37",ATTR{type}=="1", KERNEL=="eth*", NAME="eth0"
 
# PCI device 0x8086:0x100e (e1000)
SUBSYSTEM=="net",ACTION=="add", DRIVERS=="?*", ATTR{address}=="08:00:27:bd:a6:ed",ATTR{dev_id}=="0x0", ATTR{type}=="1",KERNEL=="eth*", NAME="eth2"
 
# PCI device 0x8086:0x100e (e1000)
SUBSYSTEM=="net",ACTION=="add", DRIVERS=="?*", ATTR{address}=="08:00:27:6e:86:10",ATTR{dev_id}=="0x0",  ATTR{type}=="1",KERNEL=="eth*", NAME="eth3"

--修改之后：

 
[root@ora10g network-scripts]# cat/etc/udev/rules.d/70-persistent-net.rules
# This file was automatically generated bythe /lib/udev/write_net_rules
# program, run by thepersistent-net-generator.rules rules file.
#
# You can modify it, as long as you keepeach rule on a single
# line, and change only the value of theNAME= key.
 
# PCI device 0x8086:0x100e (e1000)
SUBSYSTEM=="net",ACTION=="add", DRIVERS=="?*", ATTR{address}=="08:00:27:6E:86:10",ATTR{type}=="1", KERNEL=="eth*", NAME="eth1"
 
# PCI device 0x8086:0x100e (e1000)
SUBSYSTEM=="net",ACTION=="add", DRIVERS=="?*", ATTR{address}=="08:00:27:BD:A6:ED",ATTR{type}=="1", KERNEL=="eth*", NAME="eth0"
 

注意这里的MAC地址要和ifcfg-eth0 保持一致。 然后重启一下网卡和udev： --ifdown 网卡：

ifdown eth0
ifdown eth1
 

--重启udev

/etc/init.d/udev-post stop;
/etc/init.d/udev-post start

或者使用：

service udev-post stop
service udev-post start
 

注意： 对与Oracle linux 是udev-post, 而redhat 是udev --ifup：

Ifup eth0
Ifup eth1
 

不过在我的测试中，这2个都没有效果，我是把整个OS都重启了，才生效的。 小知识，随笔记之。 -------------------------------------------------------------------------------------------------------